Category: Trans-AM racing

From RJ Lopez in car camera


A second video from the in-car on John Baucom’s #86 Baucom Motorsports/ Mustang

In car video from John Baucom’s #86 Baucom Motorsports/ Mustang.

Video from John Baucom’s #86 Baucom Motorsports/ Mustang during the 2012 Road America Trans Am race.

Mosport Trans Am 2012. Footage from John Baucom’s #86 Baucom Motorsports/Roadraceparts Mustang.


In car video of the 2012 Road Atlanta Trans Am race. View is from John Baucom’s #86 Baucom Motorsports/ Mustang.


rontsuspension at midohio

front suspension at Mid Ohio

Talking to the team before practice at Mid Ohio they were cautiously optimistic. They feel that the track was one where being down in horsepower wouldn’t be as much of a disadvantage as somewhere like Road America. However from the very beginning the car had a significant push. They would struggle with this all day Friday.

First order of business was to try to balance the car. To do so they took a little wing out, which required drilling new holes in the mounting brackets. Then a rear spring change was made to try to correct the push issue. But neither issue corrected the problem. All during practice the team had been running on used tires, which may have masked part of the problem.

For qualifying a new set of tires was mounted and the car picked up some speed. Unfortunately everyone else did also and John qualified sixth fastest. Ahead were the Corvettes of Tommy Drissi, Doug Peterson, Simon Gregg and Amy Ruman. Cliff Ebben qualified 5th taking the honor of fastest Ford. The push was still there, but this time a “clicking” in transition was heard, which would have to be addressed.

On Saturday morning, the first order of business was to inspect all the heim joints for play. Once that issue was solved a radical spring change was made in a last ditch effort to cure the push issue. Of course the results wouldn’t be known until the race.

Rather than go into a lengthy report on the race suffice it to say that John was able to finish 4th. One more restart, which didn’t happen as they couldn’t get Amy Ruman’s car out of the sand trap in time, may have allowed him to make a run at the 3rd place finisher. But it didn’t happen, so be it.

Great race, and the dicing at the front was serious but clean. If you get the chance be sure to go out and check out the Trans Am series. Good racing and it offers something that few series do.


This is the in car camera video from John Baucom’s #86 Roadraceparts Mustang during qualifying for the 2013 Road Atlanta Trans Am race.

John's Mustang on its way to a strong 4th at Watkins Glen.

John’s Mustang on its way to a strong 4th at Watkins Glen.

Congratulations to John Baucom and the entire Baucom Motorsports team after their fine 4th place finish in the Trans Am series race at Watkins Glen today.

This was their first return to the track since the disastrous fire at Sebring in the first race of rhe season. After qualifying 5th, with a broken front sway bar he was able to get as high as 3rd where he race most of the race. However at the end he was not able to hold off Simon Gregg who took the position with just a few laps left.

Johns car after the fire at Sebring.

Johns car after the fire at Sebring.

Again congratulations to John and everybody associated with the Mustang. We look for continued success.



Ever had the mishap of a “stuck” caliper? If you have it’s probably something you haven’t forgotten. What happens is that when you apply the brakes the pistons in the caliper press the pad against the rotor and the car slows. All good, right?

But when you release the pedal the piston does not return to its seated position, allowing the pads to release the rotor. How much of a problem is that? When it happened to me a 550 hp engine could barely move the car down pit road. Not good.

Several things can cause this, just disuse, like in a car that has sat for a period of time. Or, more commonly the heat cycles that the brakes go thru eventually deteriorate the seals.

The answer, is of course to add caliper maintenance to your check sheet. Every 2 or 3 races, pull the pistons, check them over and replace the seals. Seals are cheap insurance and it could save a lot of heartache.

Brembo pressure seals available from 28-44 mm.

Brembo pressure seals available from 28-44 mm.


For those of you using Brembo calipers, they have a new design of anti-knockback seal. A direct replacement for their regular pressure seal it reduces the issue of pad knock back.

We carry AP, Alcon, and Brembo caliper seals in stock ready for immediate delivery.